LS-S5324TP-SI-AC Specification and datasheet
|Fixed port||twenty 10/100/1000Base-T ports and four gigabit Combo ports|
|Extended slot||The 5300TP provides a stacking extended slot.|
|Forwarding performance||36 Mpps|
|switching capacity||48 Gbit/s|
|MAC address table||
LI/SI: 16 K; EI/HI: 32 K
Supports learning and aging of MAC addresses.
Supports static, dynamic, and blackhole MAC address entries.
Supports packet ﬁltering based on source MAC addresses.
Supports IGMP snooping, IGMP fast leave, multicast
VLAN, IGMP proxy, controllable multicast, and port-
based multicast trafﬁc statistics.
|IPv4 routing||Supports static routing, RIP v1, RIP v2, ECMP, and URP|
|IPv6 routing||Supports RIPng, manual tunnels, 6-to-4 tunnels, and ISTAP tunnels.|
Supports Neighbor Discovery (ND).
Supports IPv6 Ping, IPv6 Tracert, and IPv6 Telnet.
Supports 6-to-4 tunnels, ISATAP tunnels, and manually conﬁgured tunnels.
Supports ACLs based on the source IPv6 address, destination IPv6 address, Layer-4
port, or protocol type.
Supports MLD v1/v2 snooping.
Supports IGMP snooping, IGMP fast leave, multicast VLAN, IGMP
proxy, controllable multicast, and port-based multicast trafﬁc statistics.
Supports rate limit on packets sent and received by a port.
Supports packet redirection.
Supports port-based trafﬁc policing and two-rate three-color CAR.
Supports eight queues on each port.
Supports multiple queue scheduling algorithms including WRR, DRR, SP, WRR+SP, and DRR+SP.
Supports WRED (supported by the S5306 and the S5300HI).
Supports re-marking of the 802.1p priority and DSCP priority.
Supports packet ﬁltering based on Layer 2 to Layer 4 information, ﬁltering out invalid
frames based on the source MAC address, destination MAC address, source IP address,
destination IP address, port number, protocol, and VLAN ID.
Supports queue-based rate limit and trafﬁc shaping on ports.
Supports STP, RSTP, and MSTP.
Supports BPDU protection, root protection, and loopback protection.
Supports the RRPP ring topology and RRPP multi-instance.
Supports the Smart Link tree topology and Smart Link multi-instance to implement
millisecond-level protective switchover.
EI/HI series support BFD for OSPF, BFD for IS-IS, BFD for VRRP, and BFD for PIM.
Supports hierarchical user management and password protection.
Supports DoS attack defense, ARP attack defense, and ICMP attack defense.
Supports binding of the IP address, MAC address, port number, and VLAN ID.
Supports port isolation, port security, and sticky MAC.
Supports blackhole MAC addresses.
Supports limit on the number of MAC addresses to be learned.
Supports IEEE 802.1X authentication and the limit on the maximum number of users
on a port.
Supports multiple authentication methods including AAA, RADIUS, HWTACACS, and NAC.
Supports SSH v2.
Supports CPU protection.
Supports blacklisting and whitelisting.
Management and maintenance
Supports intelligent stacking (The S5300HI and the S5306 do not support this
Supports MAC Forced Forwarding (MFF).
Supports Virtual Cable Test (VCT).
Supports Ethernet OAM (IEEE 802.3ah and 802.1ag).
Supports local port mirroring, Remote Switched Port Analyzer (RSPAN), and packet
forwarding on an observing port.
Supports remote conﬁguration and maintenance by using Telnet.
Supports SNMP v1/v2/v3.
Supports the Network Management System (NMS) and Web management.
Supports system logs and multi-level alarms.
Supports Dying gasp power-off alarm (the S5306 only).
Supports MUX VLAN.
Supports the Hypertext Transfer Protocol Secure (HTTPS).
Supports 802.3az EEE (the S5300HI and the S5306 only).
Operating temperature: 0°C to 50°C (long term); -5°C to 55°C (short term);
relative humidity: 10% to 90% (non-condensing)
Rated voltage: 100 V to 240 V, 50/60 Hz
Maximum voltage: 90 V to 264 V, 50/60 Hz
|Dimensions: width x depth x height||442 mm x 420 mm x 43.6 mm|
|Power consumption||< 40 W|